氣力輸送系統是一種利用氣流作為動力，實現物料在管道中遠距離輸送的工程技術。其物料進出流程通過精密設計的設備組合與氣流控制，構建了封閉、高效、低污染的物料傳輸體系。以下從系統運行邏輯出發，深度解析物料從進入至排出的完整路徑。

　　Pneumatic conveying system is an engineering technology that uses airflow as power to achieve long-distance transportation of materials in pipelines. The material entry and exit process is constructed through precision designed equipment combination and airflow control, creating a closed, efficient, and low pollution material transportation system. Starting from the system operation logic, we will deeply analyze the complete path of materials from entry to discharge.

　　一、物料引入階段：精準供料與氣流耦合

　　1、 Material introduction stage: precise feeding and airflow coupling

　　物料進入氣力輸送系統的首要環節是供料裝置。對于粉狀或顆粒狀物料，通常采用旋轉閥或螺旋輸送機實現定量給料。旋轉閥通過葉輪的間歇轉動，將儲料倉內的物料分批次送入輸送管道，其轉速可調特性確保了供料量的精確控制。螺旋輸送機則利用螺旋葉片的旋轉推動物料前進，適用于粘性較低的物料。在負壓輸送系統中，物料通過吸嘴被氣流直接吸入管道，此時需在吸嘴處設置補氣裝置，防止管道內形成真空影響供料穩定性。

　　The primary step for materials to enter the pneumatic conveying system is the feeding device. For powdered or granular materials, rotary valves or screw conveyors are usually used to achieve quantitative feeding. The rotary valve intermittently rotates the impeller to feed the materials in the storage bin into the conveying pipeline in batches. Its adjustable speed ensures precise control of the feeding amount. Spiral conveyors use the rotation of spiral blades to push materials forward, which is suitable for materials with low viscosity. In the negative pressure conveying system, materials are directly sucked into the pipeline by the airflow through the suction nozzle. At this time, an air supply device needs to be installed at the suction nozzle to prevent the formation of vacuum in the pipeline from affecting the stability of the feeding.

　　物料與氣流的耦合是供料階段的核心。在正壓輸送系統中，高壓風機或壓縮機將壓縮空氣注入輸送管道，氣流速度需達到物料懸浮的臨界值。例如，輸送水泥時，氣流速度需控制在18-25米/秒，以確保物料在管道中呈懸浮狀態而非沉積。對于易碎物料，則需采用低速高濃度輸送方式，通過降低氣流速度減少物料碰撞。

　　The coupling between materials and airflow is the core of the feeding stage. In a positive pressure conveying system, a high-pressure fan or compressor injects compressed air into the conveying pipeline, and the airflow velocity needs to reach the critical value for material suspension. For example, when transporting cement, the airflow velocity needs to be controlled at 18-25 meters per second to ensure that the material is suspended in the pipeline rather than deposited. For fragile materials, a low-speed high concentration conveying method should be used to reduce material collisions by lowering the airflow velocity.

　　二、管道輸送階段：氣流動力學與物料行為調控

　　2、 Pipeline transportation stage: airflow dynamics and material behavior regulation

　　物料進入管道后，氣流動力學特性決定了輸送效率。在水平管道中，物料受重力作用易沉積，需通過提高氣流速度或增加管道坡度來維持懸浮狀態。垂直管道中，物料在重力與氣流的雙重作用下呈現流態化特征，此時氣流速度需超過物料沉降速度的1.5倍。彎頭、三通等管道部件對物料流動產生顯著影響，彎頭處的離心力可能導致物料偏析，因此需采用長半徑彎頭或設置導流板優化流場。

　　After the material enters the pipeline, the aerodynamic characteristics determine the conveying efficiency. In a horizontal pipeline, materials are prone to sedimentation due to gravity, and it is necessary to maintain a suspended state by increasing the airflow velocity or increasing the pipeline slope. In a vertical pipeline, materials exhibit fluidization characteristics under the dual effects of gravity and airflow, where the airflow velocity needs to exceed 1.5 times the material settling velocity. Pipe components such as elbows and tees have a significant impact on material flow, and centrifugal force at the elbow may cause material segregation. Therefore, it is necessary to use long radius elbows or set up deflectors to optimize the flow field.

　　物料濃度是輸送階段的關鍵參數。低濃度輸送（物料質量濃度低于10%）適用于長距離輸送，但能耗較高；高濃度輸送（濃度達30%-50%）可降低能耗，但需解決管道堵塞風險。實際運行中，通過調節供料量與氣流量的比值，可實現濃度動態平衡。例如，在輸送塑料顆粒時，采用變頻風機與自動供料裝置聯動，使物料濃度始終維持在最佳區間。

　　Material concentration is a key parameter in the conveying stage. Low concentration conveying (material mass concentration below 10%) is suitable for long-distance conveying, but it consumes more energy; High concentration transportation (up to 30% -50% concentration) can reduce energy consumption, but the risk of pipeline blockage needs to be addressed. In actual operation, dynamic concentration balance can be achieved by adjusting the ratio of feed rate to air flow rate. For example, when transporting plastic pellets, a variable frequency fan is used in conjunction with an automatic feeding device to maintain the material concentration within the optimal range.

　　三、氣固分離階段：高效回收與能量再利用

　　3、 Gas solid separation stage: efficient recovery and energy reuse

　　物料到達終點后，需通過分離裝置實現氣固分離。旋風分離器利用離心力將物料從氣流中分離，其分離效率可達90%以上，適用于大顆粒物料。布袋除塵器則通過濾袋的微孔過濾作用捕捉細顆粒物，過濾精度可達0.1微米。對于高溫或腐蝕性物料，需采用陶瓷濾芯或金屬濾網等特殊材質分離器。

　　After the material reaches the endpoint, gas-solid separation needs to be achieved through a separation device. The cyclone separator uses centrifugal force to separate materials from the airflow, with a separation efficiency of over 90%, and is suitable for large particle materials. The bag filter captures fine particles through the microporous filtration of the filter bag, with a filtration accuracy of up to 0.1 microns. For high-temperature or corrosive materials, special material separators such as ceramic filter cartridges or metal filters should be used.

　　分離后的氣流并非直接排放，而是進入能量回收系統。在正壓輸送系統中，部分氣流通過循環風機重新注入管道，減少新鮮空氣消耗；在負壓系統中，排氣經過濾后返回風機入口，形成閉式循環。某食品加工企業通過在分離器后增設熱交換器，將排氣余熱用于物料預熱，使系統綜合能效提升。

　　The separated airflow is not directly discharged, but enters the energy recovery system. In a positive pressure conveying system, some airflow is re injected into the pipeline through a circulating fan to reduce fresh air consumption; In the negative pressure system, the exhaust gas is filtered and returned to the fan inlet, forming a closed cycle. A certain food processing enterprise has improved the overall energy efficiency of the system by adding a heat exchanger after the separator to use the exhaust waste heat for material preheating.

　　四、物料排出階段：穩定卸料與系統平衡

　　4、 Material discharge stage: stable discharge and system balance

　　分離后的物料進入儲料倉或包裝設備。為防止物料在倉內堆積，需設置流化裝置或振動器，確保物料均勻分布。對于需要連續生產的場景，采用星型卸料器或旋轉閥實現定量排出，其轉速與供料裝置聯動，維持系統壓力穩定。在包裝環節，自動稱重系統與氣力輸送系統集成，當包裝袋達到設定重量時，輸送管道自動關閉，避免過量供料。

　　The separated materials enter the storage bin or packaging equipment. To prevent material accumulation in the warehouse, it is necessary to install fluidization devices or vibrators to ensure uniform distribution of materials. For scenarios that require continuous production, star shaped unloaders or rotary valves are used to achieve quantitative discharge, and their speed is linked to the feeding device to maintain stable system pressure. In the packaging process, the automatic weighing system is integrated with the pneumatic conveying system. When the packaging bag reaches the set weight, the conveying pipeline automatically closes to avoid excessive feeding.

　　系統平衡是物料排出階段的關鍵。通過壓力傳感器實時監測管道壓差，當壓差超過閾值時，自動調節風機轉速或供料量，防止管道堵塞或物料反流。例如，在化工原料輸送中，設置雙重壓力保護裝置，當主管道壓力異常時，緊急泄壓閥開啟，物料通過旁路管道返回儲料倉，確保系統安全運行。

　　System balance is the key to the material discharge stage. Real time monitoring of pipeline pressure difference through pressure sensors. When the pressure difference exceeds a threshold, the fan speed or feeding amount is automatically adjusted to prevent pipeline blockage or material backflow. For example, in the transportation of chemical raw materials, a dual pressure protection device is installed. When the main pipeline pressure is abnormal, the emergency relief valve opens, and the material returns to the storage bin through the bypass pipeline to ensure the safe operation of the system.

　　本文由氣力輸送系統友情奉獻.更多有關的知識請點擊:http://www.1210com.cn我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from Roots blower For more information, please click: http://www.1210com.cn We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message